galaxi

You know, if you think about it, there are a ton of inventions that have been created as a means of that same process of experimentation with divergent thinking. Who knows what you could end up finding out :)

One thing that I'll add in is that I started with a similar setup, but I've heard it isn't ideal to be turning your pi on and off all the time without a proper shutdown sequence. I have my printer psu and filament dryer both plugged into smart plugs. Klipper is connected to home assistant wirelessly so I can turn them both off when prints finish, at idle, etc. My printer is in an enclosure, and the psu, pi, and mainboard both sit outside to keep them from getting hot. Pi has its own charger. I don't find it to be a burden to have the pi and psu both plugged into outlets rather than only having one plug. I find it to be a lot more stable for troubleshooting and any power issues that have come up.

Just so you know, I also started off with the teaching tech all in one electronics box. I spent a ton of hours modifying it for my particular sbc and printer. I guess I ran into issues when I would have to take out one of the boards to work on it, lol. The tolerances were really tight and it was just a pain to get it out from behind. I still have the pi+mainboard both in a box, but it's a new one I designed later on that just sits on a shelf below the printer (wires come through a hole). I find it to be really useful for printing ABS and other hot filaments and keeping a clean and tidy enclosure.

Man, we really need better labor laws.

That reminds me of an interview I did. It was a partial graphic design/videographer sort of job (my focus is in design). I was looking to break into the field, it was entry level. But the guy interviewing didn't want to fund or provide any kind of equipment like cameras. He suggested to me that I could crowdfund to get equipment so I could work for him. Seriously, lol. It was entry level pay too. Anyway, I was pretty quick to tell him I wasn't at all okay with my social circles and family funding things necessary for a new job.

There's also looria.com/reddit, which gives product recommendations based on the thoughts from different hobby subs. :)

Just incredible.

Stealth, but you can't contribute to the site (which is a benefit imo)

Changing the nozzle isn't hard, you just have to be careful. All you have to do is heat up the hotend, hold the heater block with a wrench, and use another wrench to unscrew the nozzle (you might've gotten one with your printer for this). Holding the heater block is mostly just important imo so that the torque doesn't misalign other parts in your hotend. Remember that if you're facing down, then screwing directions are reversed. So you would unscrew the nozzle clockwise (righty loosey).

After you get the nozzle off, I would push some filament through the top to get your clog out. Then you can put the same nozzle back on. The main time you would need to replace it is if you're consistently having issues even after that or you've been using it for a while (the hole gets worn through bigger over time). You can also look into doing a 'cold pull' to get out clogs.

Of course your extruder would still work fine if you didn't have anything in it because it's only jamming due to trying to push something through a clog :p You have 2 zones in a hotend: the cold end (radiator) and hot end (heater block). Sometimes a clog can happen because of heat creep, where a bit of hot melted filament gets retracted up into the cold zone and resolidifies there, blocking the passage.

Why not make a needlessly tall and unruly one that can fit all 10? :D

I for one appreciate the different angle. I like the thought that the beauty is so accessible to town.

Don't know about NewPipe, but SponsorBlock is integrated into revanced!

To add on to the other response you got, what you're experiencing is called warping (corners lifting up). Slow down your first layer, I usually do mine around 20mm/s. And yeah, clean your build plate if you are getting curling and you might've touched the plate. Hand oils transfer easily. You can take off the removable metal sheet and wash it with soapy water. You can also spray or drip rubbing alcohol and wipe with a paper towel between prints. Use a brim and make sure your first layer height is perfect (too far can cause it to not stick well enough, and too close can cause a clog or messy layers). The first layer is the most important for a perfect print.

When you get a new filament, do be sure to check the temperature recommendation on the side of the spool. Sometimes different brands print at different temps. Different types, like PLA and PETG, print at different temps too.

If you got clippers with your printer, they can be used for a lot of things. You can cut stuff off of your prints. Typically what I use mine for is cutting the end of the filament into a point before I insert it into the printer so that it goes in more easily. If you pull used filament out, it will typically be melted and blobby on the end and harder to reinsert.

People will probably give me flak for this but I use the metal wire brush that came with my printer and brush it on the nozzle while it's hot. You can buy extras online. It does wear the nozzle down 'sooner' since it's abrasive, and it makes a bit of a mess, but it's way more effective than trying to wipe it off imo. Cleaning the nozzle isn't super necessary, but it will keep bits of charred filament from getting into your print and will help the nozzle last longer until you change it.

As for the question about putting your printer away, you don't have to do that. I would be more worried about the people sticking their fingers in or near the printer than about the printer itself, lol. 3D printers have really strong frames and motors. They are really easy to take apart and replace things as needed, unlike something like a computer which is a bit more delicate with more electronics. I typically pick mine up by the top bar if I need to carry it anywhere. Just make sure that the printer is somewhere where it won't hit anything if the bed is sliding out, and that as it's homing or moving, the head and the bed aren't going to catch on any wires. Do be careful with the motors if you're ever interacting with the printing while it's moving, they don't care if there's something in the way. :p

Like I said on your last post, I'm happy to help if you have any other questions 👍 I'm happy you've been enjoying your experience so much! 3D printing is the best hobby!