Nyxon

No, on the X there is a lever just below the open door button on the front doors. I have seen multiple people use it instead of the button because the button in the front door is less obvious to them then the lever.

Sounds like you are being haunted by these wooden bowls but all they want is to be useful. I think you have friends in the spirit world.

I only saw it as a duck, it took your comment for me to look again and see the eagle. You are not alone!

Do you have anything for the qbittorrent app on a Mac that would make it dark mode? Because last time I used it the app didn’t have a dark mode.

But what about the ads on the website, the site might be dark mode enabled but are the ads?

Yep, gottem… it does not have dark mode… but hold on here…

Do the ads on torrent sites adhere to dark mode standards?

qittorrent has a search function where you input and save the associated plug-in/address of the torrent site/feed you want and then you can just search within qbittorrent for whatever torrent you are looking for and select whatever you want for download without having to go to an website or another app/protocol.

Avocado oil is what I use. It has the highest smoke point of the readily available cooking oils, is supposedly healthier than other oils, has a clean flavor and doesn’t peel once polymerized for me. Olive oil works, and so does various other fats; bacon, tallow, butter etc.

I use my cast iron more than any other pans because it is more versatile than my carbon steel or stainless steel pans. Each have their own place but cast iron works for more of what I do. The cast iron absorbs heat and works well for doing high heat cooking so having an oil that doesn’t burn until higher temps gives more temp ranges to operate in. When an oil/fat goes past it’s smoke point it becomes a carcinogen and is unhealthy to breath/eat. So avocado oil’s smoke point just over 500° is better than olive oil at around 300°-350°f.

Yeah, exactly, my brain substituting in the change of two letters and reading it like that caused a double take, especially because the last sentence was where it happened it made the comment feel more like a punchline than a statement.

I also found it interesting in how changing just two letter in an entire comment could change the whole meaning of the comment in my brain.

Honestly, when I first read your comment I read “I’ve been able to accomplish” not “It’s been able to accomplish” and thought to myself… yeah, look, this is good research with tons of benefit potential for the world but maybe these laws are in place because DIY scientists with home labs shouldn’t be messing with it just yet, I mean, that sounds reasonable. The meme provided also kinda could be taken either way in the “I’ve”, “it’s”

But yeah, it took only a few seconds to re-read it and find my mistake. I had figured you were joking with the “I’ve” thing to prove a point, not that you were really experimenting with stem cells at home. Either way, it was a fun mental rabbit hole for about 5 seconds. So thank you.

And I agree with you, we should be funding this type of scientific research.

Ah ha! Thank you, this was one of my worries with increasing the capacity, I was worried that even after replacing the 4TB drives with larger capacity drives that the new drives would still only be limited to the lower capacity partitions. I wasn’t sure if there was a way to increase them.

My work around for this was to back up all the data on the NAS currently (only ~7.2TB) onto an external drive. Put the new larger capacity drives into the NAS, format them properly and setup the RAID as needed and then transfer the data back onto the new fresh larger capacity drives in the NAS from the external drive.

1. Cool, thank you for you input on using larger drives. I figured it could but wanted to be sure before spending the money.
2. I know the PR4100 will rebuild itself if you remove a faulty drive and replace it with a new one, I am just not sure how it would work when upgrading the size and if there would be a better way to go about doing so than just letting the PR4100 do the work itself.

Thank you for your thorough response!

I figured there wouldn’t be an upper limit but I’ve been burned before in the past with trying to use too big of a drive in various applications over the past 3 decades of computer use so I wanted to be sure before dropping a lot of money on new high capacity drives for the NAS.

When I replaced the one drive a few months ago I just removed the faulty drive from the NAS and slotted in the new drive in its place and the NAS copied everything and was up in running again in a few days. It was only 4TB but it took awhile. I know it should be able to if I replace like for like sized drives but I wasn’t sure how it would be have if I start replacing 4TB drives with 20tb drives.

I do have a drive cloner already, buried in an old tech box in the garage that I could use but it is several years old (6 maybe?) so I am sure it isn’t as fast a a newer one. Maybe I will pick up one or two of the ones you suggested to speed the process along.