I have only put a clutch in one front wheel drive car. It failed in front of the truck shop I worked at and that's where it was brought to. Anyway, the clutch disc exploded and put a lot of side loading on the input shaft. This car exhibit similar issues to yours. The shift lever felt terrible until the unit was removed from the machine. Maybe your input shaft isn't lined up well or there is something wrong with that bearing. Pull it out. We make mistakes ๐
this post was submitted on 10 Mar 2024
9 points (100.0% liked)
Mechanic Advice
275 readers
1 users here now
This community is for getting help with vehicle or other mechanical problems.
Remember, there are no stupid questions, we want everyone to feel welcome. If you don't want to answer a question that you think is silly, then just move on and keep it to yourself.
Rules:
- Don't be a dick
That is all.
founded 1 year ago
MODERATORS
Thank you for replying ๐ In this car's case, the clutch was worn down to bare metal. Do you think maybe I could have bent the input shaft and this could cause it? I don't hear any unpleasant sounds of uneven rotation though, which I might expect from that (based on no experience at all ๐)
Also what machine was it you mentioned?
It seems you may have the problem "fixed" but this machine was, I think, a 2008 or so Kia. Optima? I am in the US. I looked it up, and in markets that I think Dacia would be in, it may be Magentis. There were many unpleasant sounds when this car arrived...
Anyway, it is pretty hard to bend the input shaft. Even this catastrophic failure did not do that. It destroyed the flywheel (which was expensive) and that was the big financial challenge for the owner (who was Brazilian). They did not like the price of that part, it was half of the total cost. My information was just to add to the discussion. The car left with new part and was fine.
I hope you can get on your way!
I thought it was unlikely I'd managed to damage it even before you said that, now I'm sure ๐
Thank you for your kind words. It's back on the road now and just as good, if not slightly better than before the clutch started slipping.
Year make model would be very helpful.
Did you do the clutch yourself? If so did you take the engine or transmission out?
Based on what info you gave it sounds like you have an issue with a selector fork.
It's a 2013 Dacia sandero II - 1.5DCI
Yes, I did. I didn't actually fully remove the transmission to avoid removing the front subframe. There was just enough space to separate the gearbox and engine and slot the new clutch assembly in.
I think it sounds like a single selector fork too, but I can't think how I could've damaged it, since I don't think I have done anything that should affect the internals of the gearbox ๐ข
Okay, I am going to guess that when you spit the bell housing you moved the transmission and not the engine. I am also going to bet that you didn't disconnect the shifter linkage first. I am not saying it is likely but as you moved the transmission it is possible that the link pulled on a selector fork (is it cable linkage?)
So this is what I would do to try to narrow the fault down. Jack up one drive wheel and put it in gear. With the engine off the wheel shouldn't turn. Now leaving it in gear and push the clutch in, the wheel should now turn. If that is normal it is most likely not the clutch.
Now disconnect the shift linkage at the transmission. This should free the shifter. So make sure that it moves freely.
Lastly with the shift linkage disconnected and the clutch pushed in see if you can move the selector forks by hand.
That should narrow it down for you
Even a selector fork that is a little bent can really screw with shifting, it can sometimes make the transmission be in two gears at the same time.
I could also see this fault happening with a damaged clutch basket/fingers or a bad slave cylinder. Did you leave the slave cylinder attached to the hydraulics? Some clutch hydraulic systems are unbleedable. If you did some that could have gotten air in the system. Does the clutch feel normal?
I left it overnight, and now the gear change is back to normal and I have no idea why ๐ญ
That's a really great way to find the problem, and if it starts happening again I will follow exactly that process ๐
It may not matter now, but for the sake of completing the picture:
- I did move the gearbox but I also disconnected the linkage beforehand, carefully and gently too.
- It's a bleedable (concentric) slave cylinder which I replaced with the clutch as it has an integrated release bearing. I've now been able to test the clutch properly and it feels excellent ๐
If the problem comes back and I am able to find the cause, I will make sure to report back!
Well good I guess...
That is weird. It seems like you did everything right. I can't really see why this would happen. With it going away like that it seems like it must be something to do with the clutch... Maybe it didn't seat properly and you fixed it when you were trying to diagnose it. Or maybe you had some weird air pocket in the clutch hydraulics that needed time to rise to the top.... I don't know
I would keep an eye on your clutch hydraulic fluid for a bit just to be safe. Otherwise just be happy it went away. I know I hate not knowing what was wrong even when it gets fixed.
Or as I think maybe you had a selector fork get stuck and it released overnight....
I will watch the fluid level or maybe even bleed it once more then, but it seems it's going to remain a mystery for now anyway.
I really appreciate you going to the trouble to try and help with this. Thank you very much ๐
I'm assuming this problem didn't exist before replacing the clutch. I'd look at anything linkage related, possibly mounts / bell housing bolts that might be throwing alignment of the transmission off. Something has to be putting pressure on the forks in a weird way to make it behave as you describe.
Thank you ๐ I'll go and look / feel where the linkages attach after I've finished writing replies ๐
What car is it?
It's a 2013 Dacia sandero II - 1.5DCI