this post was submitted on 20 Feb 2024
-2 points (45.8% liked)

Cast Iron

2037 readers
1 users here now

A community for cast iron cookware. Recipes, care, restoration, identification, etc.

Rules: Be helpful when you can, be respectful always, and keep cooking bacon.

More rules may come as the community grows, but for now, I'll remove spam or anything obviously mean-spirited, and leave it at that.

Related Communities: !forgediron@lemmy.world !sourdough@lemmy.world !cooking@lemmy.world

founded 1 year ago
MODERATORS
 

You are already getting the pan hot enough to sear, just leave it there a little while longer and it's cooked!

top 12 comments
sorted by: hot top controversial new old
[–] ChicoSuave@lemmy.world 11 points 9 months ago (1 children)

Cooking steak is about accurately applying heat. Getting a good quality internal cook without drying out or overcooking the outside is a challenge and nearly impossible with a single pan unless it's a long, low heat with a high heat sear at the end for the Maillard reaction. Because of the need to have such different heats, it takes a long time OR requires 2 pans.

Neither is your approach, which wouldmake a fine steak. But I want a great steak and one pan is not capable of a great steak.

[–] SkyezOpen@lemmy.world 3 points 9 months ago (2 children)

one pan is not capable of a great steak.

Sous vide says one pan for perfect steak.

[–] jeeva@lemmy.world 4 points 9 months ago* (last edited 9 months ago)

I'd argue that you're massively stretching "one pan" and perfect steak, here... But as said, to each their own (perfect steak).

For me, the crust formed after a reverse sear is way better than that after a sous vide, without more effort.

[–] littlebluespark@lemmy.world 2 points 9 months ago

To each their own.

[–] DredPyr8Roberts@lemmy.world 10 points 9 months ago

For a thin steak, I agree. However, a thick cut of meat requires a longer cook time and the crust applied at the beginning of the cook tends to lose its integrity. Cooking longer and slower first allows one to apply the desired temp evenly throughout a thick cut, then searing last reduces and even eliminates the tough grey outer layer.

[–] DScratch@sh.itjust.works 3 points 9 months ago

It’s very difficult to get a steak medium-rare with a good char outside by just frying it.

[–] verdantbanana@lemmy.world 3 points 9 months ago (1 children)
  1. preheat oven to the lowest temperature it will allow trying not to go above 225 degrees Fahrenheit

  2. season steaks your way in a glass bakeware dish and leave uncovered sitting on the counter

  3. place cast iron or carbon steel on stovetop and preheat on 1 until the steaks in the oven are done making sure to keep the cookware wet with preferred oil at a very thin layer

  4. cook steaks in oven still leaving uncovered until center internal temperature reaches 125 for rare or 135 for medium and 140 for well this may take thirty minutes up to an hour

  5. set the burner the cast iron or carbon steel is on to two

  6. after a few minutes cook steak on the cast iron or carbon steel for thirty seconds on each side

[–] Anticorp@lemmy.world 3 points 9 months ago (1 children)

What is 1 and 2 burner setting? Idk if you mean low and medium low, or high and medium high.

[–] verdantbanana@lemmy.world 2 points 9 months ago

all the way low and just above low

[–] aodhsishaj@lemmy.world 2 points 9 months ago (1 children)

How do I reversensear a steak? Is that a Dutch technique only applicable to the ovens?

[–] bitwaba@lemmy.world 1 points 9 months ago
[–] Drusas@kbin.social 1 points 9 months ago

Cook sous vide then sear. Perfectly done steak.