3DPrinting
3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
The r/functionalprint community is now located at: !functionalprint@kbin.social or !functionalprint@fedia.io
There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml
Rules
-
No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
-
Be respectful, especially when disagreeing. Everyone should feel welcome here.
-
No porn (NSFW prints are acceptable but must be marked NSFW)
-
No Ads / Spamming / Guerrilla Marketing
-
Do not create links to reddit
-
If you see an issue please flag it
-
No guns
-
No injury gore posts
If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is 
Moderation policy: Light, mostly invisible
view the rest of the comments
All printers use the same components. Same motors, leadscrews and belts. If the printer is built well, the precision will be the same. You obviously have play in some machines, but due to the variance in filament it can vary from negligible to basically nonexistent. It's not the machines fault most of the time. Polymers have variance and sometimes unpredictable behaviour. Just part of the game.
From your recommendation, I'm leaning towards the Sovul printer. What has been your experience with it, like ease of use, proneness to breakages, or anything else unexpected from the Amazon page?
So I have used the sv06 and had a bit of a run in with the sv07. Both are decent machines with their own quirks. The sv06 needs bearings replaced after 3 months of use at the latest, after that runs perfectly. The sv07 uses v-wheels, and is therefore lower maintenance. They both use the same toolhead design and both print well enough. sv07 is a bit more finnicky with cooling (special klipper command for the big fan) but they are both decent machines. I personally run a heavily modified Ender 3 v2, but currently, the Sovols are some of the best bang for the buck. Right now, I would buy the sv06, change the bearings from day one and that's it. It is basically a 1:1 copy of a Prusa, and printing replacement parts for it is extremely easy, if anything ever breaks. The only thing it "lacks" is a filament sensor (haven't had the need for one in the time I have been printing), but that is easily added. Do your own research though. Lost in Tech has some great reviews on both machines.
The SV07 (just now) the firmware almost immediately broke after I put it together, powered it on, started it autoleveleling and the stopped it because it was screeching, and the rebooted it. Now it won't power on without showing green text, or doesn't progress past the loading screen, or doesn't turn on at all. It's different every time.
What country are you located in?
Uk. The firmware suddenly resolved itself, but now the y axis (the bed) doesn't seem to be moving properly, it tries to move off where it can't, and says 'out of range' to moving where it can.
Just in case, check the PSU Voltage. Check the plugs on the Y axis motor. Worst case, you might need to redownload the CFG file for your printer. Try that. Write again if none of that works.
Thanks for outlining the steps, but I'm not sure what each thing you recommended entails. Are you able to explain it in more detail please?
So, the PSU voltage switch is for setting input voltage. You might be running it on 110V instead of 230V, though unlikely but it doesn't hurt to check.
Checking the y motor and endstop wiring I recommended because I had a similar problem on my x-axis when my motor wire and endstop wire came loose, where the motor was jittering and buzzing, but not moving.
The .cfg file is the configuration file for Klipper firmware, which is taylored for your printer. Since you said that your firmware issues got fixed I don't think that's it, but if nothing else, redownload and reinstall the .cfg file and if that does not help, reinstall klipper as a last resort. Do so only if nothing else helps.
If you need more help, I could help you through video chat. Just DM me.
If anyone is interested, the problem was due to packing material not being completely removed from under the printbed.