Linux

48090 readers

675 users here now

From Wikipedia, the free encyclopedia

Linux is a family of open source Unix-like operating systems based on the Linux kernel, an operating system kernel first released on September 17, 1991 by Linus Torvalds. Linux is typically packaged in a Linux distribution (or distro for short).

Distributions include the Linux kernel and supporting system software and libraries, many of which are provided by the GNU Project. Many Linux distributions use the word "Linux" in their name, but the Free Software Foundation uses the name GNU/Linux to emphasize the importance of GNU software, causing some controversy.

Rules

Posts must be relevant to operating systems running the Linux kernel. GNU/Linux or otherwise.
No misinformation
No NSFW content
No hate speech, bigotry, etc

Related Communities

Community icon by Alpár-Etele Méder, licensed under CC BY 3.0

founded 5 years ago

MODERATORS

AgreeableLandscape@lemmy.ml

nooter692@lemmy.ml

MarcellusDrum@lemmy.ml

cypherpunks@lemmy.ml

cyclohexane@lemmy.ml

d3Xt3r@lemmy.nz

UPDATE: I successfully dual booted Linux! and then I messed up... (lemmy.ca)

submitted 1 year ago* (last edited 1 year ago) by otter@lemmy.ca to c/linux@lemmy.ml

30 comments fedilink hide all child comments

Update from this post from the other day: What to know before Dual Booting Windows + Linux?

TLDR: I got it working, started learning, tried to fix a grub issue and borked the whole system.

So after considering all the advice, I went and disabled/prepped/backed up, and started the process. I managed to get Fedora KDE installed on another partition and everything was looking ok. I installed some programs, started learning for a few hours, but there was one small issue. The grub configuration from the video didn't really work. Windows wasn't booting by default, and when I tried to do the GRUB_SAVEDEFAULT=true to have it boot the last OS, it also didn't work. When booting windows, a message would flash by saying '/EFI/fedora/grubenv' not found.

Looking more into it, the video says to use sudo grub2-mkconfig -o boot/efi/EFI/fedora/grub.cfg but I think the correct one now is grub2-mkconfig -o /boot/grub2/grub.cfg? I found this thread, but I couldn't run the first command because it gave a conflict error, and I think there were two versions of grub2 installed?

So anyways, I tried running the setup again, thought it was ok and did a reboot to test... and got hit with a black screen with minimal BASH like line editing is supported.

At this point I'm a little worried and lost, thinking maybe I wasn't ready to try this, and trying to get it back the way it was. I found this guide, but I get stuck trying to mount the EFI partition.

Any tips on where to go from here? Right now I plugged in the USB I used earlier, booted Fedora from it, and opened the terminal. Past that I'm a bit lost on how to fix grub.

you are viewing a single comment's thread
view the rest of the comments

[–] ebits21@lemmy.ca 32 points 1 year ago* (last edited 1 year ago) (2 children)

Lesson I also learned when I started out with Linux… don’t fuck with grub unless you really understand what you’re doing! Borking grub is a right of passage imo.

I’m not sure how to fix your issue (I gave up on dual booting and just have windows in a virtual machine, so Windows doesn’t mess up grub).

I always keep backups of the working grub config in case I need to restore. Just boot into a version of Linux on a usb key and copy the working config.

[–] Frederic@beehaw.org 4 points 1 year ago

oh yes, did it multiple times... Now I'm using MX Linux, if I break something, I boot on the USB disk and click on the "repair boot", and tada! it works again. But yeah I always keep a backup of my EFI in case of too.

Grub is still better than LILO :)

[–] otter@lemmy.ca 3 points 1 year ago (1 children)

I'll have to give this another try tomorrow when I'm more awake. I probably should have just asked here when I had grub issues in the first place.

Just boot into a version of Linux on a usb key and copy the working config.

So I guess this is what the guides are saying, but I seem to get stuck on the installation step with this error grub2-install: error: this utility cannot be used for EFI platforms because it does not support UEFI Secure Boot. Hopefully I understand it better once i'm more awake. Thank you though!

[–] datavoid@lemmy.ml 7 points 1 year ago (1 children)

You need to turn off secure boot in your bios maybe

[–] krankykrio@lemmy.world 1 points 1 year ago

Turning off secure boot in bios did the trick for me when I setup Mint with Windows 11.