3DPrinting

15519 readers

119 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: !functionalprint@kbin.social or !functionalprint@fedia.io

There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml

Rules

No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
Be respectful, especially when disagreeing. Everyone should feel welcome here.
No porn (NSFW prints are acceptable but must be marked NSFW)
No Ads / Spamming / Guerrilla Marketing
Do not create links to reddit
If you see an issue please flag it
No guns
No injury gore posts

If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 1 year ago

MODERATORS

andypiper@lemmy.world

henry_rowengartner@lemmy.world

j4k3@lemmy.world

GrayBackgroundMusic@lemm.ee

Major issues with klipper and bed levelling (feddit.dk)

submitted 9 months ago* (last edited 9 months ago) by Grippler@feddit.dk to c/3dprinting@lemmy.world

15 comments fedilink hide all child comments

I recently made the switch from the marlin-based stock firmware on my anycubic kobra 2, to klipper. I didn't have issues with bed levelling or first layer on the stock firmware, but I'm having significant issues running klipper. The bed is uneven, the probed mesh shows a deviation of 0.197mm, it was the same when running stock FW+octoprint.

But it seemed to be correcting just fine for this on the stock FW. I got a consistent decent first layer across the entire bed.

With klipper, it's absolutely impossible to get it to correct for this unevenness. Half the bed will get perfect first layer, but then the second half is either way too squished or hardly connecting to the bed. And it's causing further issues as it's also hitting the print when moving, despite having Z-hop of 0.3mm for travel moves.

What the hell is going on? How do I fix this?

you are viewing a single comment's thread
view the rest of the comments

[–] morbidcactus@lemmy.ca 1 points 9 months ago* (last edited 9 months ago)

What type of probe and what's the config on it?

[probe]
pin: PC14
x_offset: 23
y_offset: 5
#z_offset: 0.10
speed: 20.0
samples: 5 
samples_result: average
sample_retract_dist: 1.0
#samples_tolerance: 0.010
#samples_tolerance_retries: 10

Is what I've got my pinda probe configured with, was playing around with sample tolerances like I have on my printer with a tap probe but I just found the inductive probe has a lot of variation, I added more samples to hopefully average out that error.

[Bed_mesh]
algorithm: bicubic
fade_start: 0.6
fade_end: 10.0
bicubic_tension: 0.2
faulty_region_1_max: 120.0, 74.0 
faulty_region_1_min: 85.0, 45.0 # 103,69
faulty_region_2_max: 125.0, 165
faulty_region_2_min: 70, 110 # 103, 137
horizontal_move_z: 2
mesh_max: 228,210
mesh_min: 24, 6
mesh_pps: 2, 2
probe_count: 5,5
speed: 200

Is my mesh setup, based on a mk3s klipper config. Meshes look a little odd but I ran some bed level prints fine and just ran a full plate of abs with pretty consistent 1st layer.